Skip to content

Rear Derailleur Adjustment: Limit Screws, B-Tension and Indexing

Fix skipping, hesitating and noisy shifts in the right order.

By Medell. Editorial2 min read
Black-and-white close-up of a rear derailleur
Fidel Fernando / Unsplash

Before you start

Difficulty
Intermediate
Estimated time
30 min

Tools required

  • •Repair stand (or a helper to lift the rear wheel)
  • •2 mm or 2.5 mm hex key
  • •Small Phillips screwdriver
  • •Cable cutters (if replacing cable)

Safety

  • •Never put fingers near the spokes or chain while pedalling the bike in a stand.
  • •If the derailleur hanger is bent, have it aligned before adjusting anything else.

Before reaching for the barrel adjuster, confirm the basics: the derailleur hanger is straight, the cable and housing are in good condition and the chain is not worn. Adjustments cannot fix damaged parts.

1. Set the limit screws

The H (high) and L (low) screws stop the derailleur moving past the smallest and largest cogs. Adjust them with the cable slack so you are setting physical limits, not indexing.

2. Set B-tension

The B-screw sets the gap between the upper jockey wheel and the cassette. Follow the gap recommended by your derailleur's manufacturer, measured in the largest cog.

3. Index the shifting

  1. 01

    Tension the cable

    Shift to the smallest cog, pull the cable taut and clamp it.

  2. 02

    Shift up one cog

    If the chain hesitates, add tension by turning the barrel adjuster anticlockwise a quarter turn at a time.

  3. 03

    Check across the range

    Shift through every gear. If it overshoots on the way down, remove tension slightly.

Common shifting problems and likely causes

SymptomLikely cause
Hesitates shifting to bigger cogsCable tension too low
Hesitates shifting to smaller cogsCable tension too high or dirty housing
Skips under hard pedallingWorn chain or cassette, or poor indexing
Chain falls off the largest or smallest cogLimit screws set too loose
Shifting fine in some gears, poor in othersBent derailleur hanger

Frequently asked questions

How do I know if my derailleur hanger is bent?

Look at the derailleur from behind the bike. The jockey wheels should line up vertically under the cogs. If the cage tilts toward the wheel, the hanger is likely bent. A shop can straighten it with an alignment tool or replace it.

What does the B-screw actually do?

It sets how close the upper jockey wheel sits to the cassette. Too close and it grinds on the large cogs; too far and shifting becomes slow and vague.

Why did my shifting go out after fitting a new wheel?

Cassettes can sit in slightly different positions on different hubs. Re-index with the barrel adjuster; small changes usually fix it.

Up next · 2 min readHow to Check Chain Wear and Know When to Replace Your Chain →

The Medell. Letter

New rides, workshop guides and reviews, in your inbox.

Free. Every two weeks, never daily. One-click unsubscribe. See our privacy policy.

Drivetrain

How to Clean and Lube a Bicycle Chain

A clean, correctly lubricated chain shifts better, runs quieter and wears your cassette and chainrings more slowly. Here is the full routine.

Beginner20 min job
Drivetrain

How to Adjust a Front Derailleur

Chain dropping or not reaching the big ring? A step-by-step guide to setting front derailleur height, angle, limits and cable tension.

Intermediate30 min job

The Medell. Letter · Free

Free. Every two weeks, never daily. One-click unsubscribe. See our privacy policy.

  1. 01One workshop fixA repair you can do this weekend, with tools and time listed.
  2. 02One road worth ridingRoutes and rides from around the islands.
  3. 03Gear notes, honestly labelledHands-on or research-based, always said up front.